Macro to open floating mixer, channel editor and one macro folder?

[Havoc911]

OK, we will also post the Cubase version.

Nice I'm excited to try this!

[Home Studio 87]

Cooooooool

[Tumppi]

Boy this is nice customer service don’t you think!?
I think we have a killer product here...

[Havoc911]

Boy this is nice customer service don’t you think!?
I think we have a killer product here...

Absolutely! I'm so glad I didn't get a Slate Raven.

[Tumppi]

Hey, I found a small but important need for improvement...
These Nuendo workspaces we need to make and save: in the project window it includes Nuendos zoom settings and where in the timeline Nuendo was when it was saved.
So every time I go from mixing workspace back to editing using "recall Dtouch Ws - editing" macro it "forgets" where I was and what zoom I had. Not nice. I need to go back where I left from the project. Hope I make sense...

Bye / Tumppi

[DT_bettinzana]

Hey, I found a small but important need for improvement...
These Nuendo workspaces we need to make and save: in the project window it includes Nuendos zoom settings and where in the timeline Nuendo was when it was saved.
So every time I go from mixing workspace back to editing using "recall Dtouch Ws - editing" macro it "forgets" where I was and what zoom I had. Not nice. I need to go back where I left from the project. Hope I make sense...

Bye / Tumppi

We had an idea. No sure that it will work well for you. Tomorrow we will post the new macros for your testing.

[Tumppi]

Excellent!

[Support Team]

OK, we finished updating the Macros, including all your suggestions collected so far.

Hey, I found a small but important need for improvement...
These Nuendo workspaces we need to make and save: in the project window it includes Nuendos zoom settings and where in the timeline Nuendo was when it was saved.
So every time I go from mixing workspace back to editing using "recall Dtouch Ws - editing" macro it "forgets" where I was and what zoom I had. Not nice. I need to go back where I left from the project. Hope I make sense...

Bye / Tumppi

We fixed this behavior by sending a "Workspaces >> Update Workspace" Keycommand at the start of each of these Macros, which will overwrite the current Workspace with the current settings.
Now you need to be careful about new windows, changed positions, etc... because these will be saved in the Workspace!

Let's proceed with the new Macros...



Generic Macro

Is it possible to make it so that these Nuendo workspaces don't need to be #1 and #2 but one could customize that also and with this one could also multiply these DTouch workspaces for many different situations like tracking, mixing, editing, adr:ing etc...

Bye / Tumppi

Here you are: this is a generic Macro, which can be thought as the "Template Macro" on which the following Macros are based.

Recall DTouch Workspace - Generic [Nuendo].dat

(3.75 KiB) Downloaded 526 times

Like before, this Macro (and the following ones) needs you to:

• Open the wanted DTouch / Nuendo windows, and place them to the wanted positions
• Add a new Nuendo Workspace, and position it on one of the first 9 Workspaces. Take note of the position in the Global Workspaces list, you'll need to configure the Macro with this position number.
• Edit the first Macro Command, which contains the Macro Configuration

Some explanations about the Macro Configuration (first Macro Command):

Code: Select all

# Number of Nuendo workspace to recall (1 to 9)
nuendo_workspace_nr = 1

Insert here the position in the Global Workspaces list of the wanted Workspace to recall

Code: Select all

# List of DTouch Macro Folders to open
# Example:
#	macro_folders_to_open = () --> Don't open any folder
#	macro_folders_to_open = ("xxx1", "xxx2") --> Open folders "xxx1" and "xxx2"
macro_folders_to_open = ("DT Folder 1", "DT Folder 2")

Populate the Python tuple with the names of the DTouch Folder to be opened.
Special case: a Python tuple with only one element is written as:

Code: Select all

("One Folder", )

Code: Select all

# Set "show_floating_mixer" to True to open a DTouch Floating Mixer;
# Set it to False to close all DTouch Floating Mixers
show_floating_mixer = True

The code comments already explain this well; if this is set to False, the following settings are ignored

Code: Select all

# DTouch Floating Mixer number to open
floating_mixer_nr = 1

This is already well explained, too

Code: Select all

# Set "change_floating_mixer_properties" to False to use current DTouch Floating Mixer properties;
# Set it to True to use following values...
change_floating_mixer_properties = True
floating_mixer_x = -7
floating_mixer_y = 537
floating_mixer_w = 1770
floating_mixer_h = 545

If you want to open the DTouch Floating Mixer using its current position and size, set "change_floating_mixer_properties" to False. The following settings will be ignored.
Otherwise, set it to True, and then populate the following settings with the wanted position and size.



Updated Mix / Project Macros
The Mix Macro is currently configured to recall the first Global Workspace, the Project Macro is configured to recall the second one.

Recall DTouch Workspace - Mixing [Nuendo].dat

(3.75 KiB) Downloaded 499 times

Recall DTouch Workspace - Editing [Nuendo].dat

(3.74 KiB) Downloaded 569 times

Cubase Macros

Yes could really use this for cubase since I lost that function after the 9.5 changes.

These Macros are exactly like the previous ones, but they are in the DTouch for Cubase format

Recall DTouch Workspace - Generic [Cubase].dat

(3.75 KiB) Downloaded 543 times

Recall DTouch Workspace - Mixing [Cubase].dat

(3.75 KiB) Downloaded 535 times

Recall DTouch Workspace - Editing [Cubase].dat

(3.75 KiB) Downloaded 501 times

[Tumppi]

Hey!
Will try this when have the spare time. Thanks!

Can these macros be duplicated, renamed and thus made to different workspaces to different situations?

Bye / Tumppi

[Home Studio 87]

Code: Select all
# DTouch Floating Mixer number to open
floating_mixer_nr = 1

How can I Open 2 floating mixer at the same time ?